e4f37082c2
Two small improvements to the OpenWrt gateway deploy tutorial: - Add a router-side ping step at the top of Step 4 (post-gateway-start client test). Confirms the router itself reaches the mesh before bringing the LAN segment into the diagnosis: if this fails the troubleshooting target is the daemon / mesh side; if it succeeds and the LAN-client test below fails, the target is the LAN segment (proxy_ndp, RA pool route, or DNS forwarding through dnsmasq). - Mark the inbound port-forward section heading as Optional. The outbound half is the steady-state use of a gateway and applies to every deployment; the inbound port-forward half is a per-service opt-in that many operators won't need.
Tutorials
If you have just installed FIPS, this is where to start. The tutorials below take you from a freshly-installed daemon to a node that:
- Has joined the public test mesh and can reach other nodes on it.
- Carries a stable identity that other operators can address.
- Discovers peers — and is discoverable — over Nostr.
- Hosts and consumes real services across the mesh.
Each tutorial is a complete, working session at the keyboard. You configure something, restart the daemon, watch it come up, and verify the result. The point is to build muscle memory, not to cover every option.
Read them in order. Each tutorial assumes the state the previous one left you in. If you skip ahead, the cross-references that lead you back may not match what you have on disk.
The new-user progression
| # | Tutorial | What you'll do |
|---|---|---|
| 1 | join-the-test-mesh.md | Add one public test peer to your config, watch the link come up, ping that peer and a second mesh node it routes you to. The starting point for everything else. |
| 2 | persistent-identity.md | Pin your daemon to a stable Nostr keypair so your address stops changing on every restart. Other operators can now add you to their peers: lists; the services you host get a fixed name. |
| 3 | resolve-peers-via-nostr.md | Stop hard-coding peer addresses. Drop the address line from your peer entry and let the daemon look up the current endpoint from public Nostr relays at dial time. |
| 4 | advertise-your-node.md | Publish your own UDP endpoint to Nostr so any operator who knows your npub can reach you, with a short final section on udp:nat traversal for symmetric-NAT networks. |
| 5 | open-discovery.md | Switch to policy: open and let your peer list populate itself from the ambient fips-overlay-v1 namespace. Hands-off mesh participation. |
| 6 | reach-mesh-services.md | Drive ordinary IPv6 tools — ping6, nc, traceroute6, curl, ssh — at mesh nodes by <npub>.fips. Get a feel for the daemon's IPv6 adapter, which makes unmodified IPv6 software work over the mesh. |
| 7 | host-a-service.md | Bring up an HTTP server bound to fips0 so mesh nodes can reach it, with a deliberate exposure decision (mesh-only vs every interface), and the mesh firewall as a default-deny baseline. The peer ACL (a separate, transport-layer control over which npubs may peer with your node) is briefly mentioned alongside. |
| 8 | ground-up-mesh.md | Bring up a second deployment mode: two devices joined by Ethernet (or WiFi, or BLE) with no IP infrastructure between them. The mesh emerges from layer 2 up. Coexists with overlay peers — the same daemon can carry both. |
After tutorial 8 you have a fully participating mesh node that reaches services hosted by other mesh nodes and hosts services of its own, with identity, discovery, reachability, an explicit exposure policy, and an understanding of both deployment modes — overlay on top of existing IP, and ground-up where the mesh is the network.
There is also a side trip you can take any time after tutorial 1:
- ipv6-adapter-walkthrough.md —
trace one
sshfrom DNS query through session setup to the far-side TUN, usingfipstopandfipsctlto watch each step. Optional, but if you like seeing how the pieces fit together, this is the doc that shows you.
Advanced
These are not part of the new-user progression. They assume you have already worked through the tutorials above and now want to fold FIPS into a wider network deployment.
- deploy-fips-gateway.md — Stand up a
fips-gatewayon an OpenWrt access point so unmodified LAN hosts can reach<npub>.fipsdestinations through a DNS- allocated virtual IPv6 pool and kernel nftables NAT, with no per-host FIPS install. Also walks through one inbound port forward exposing a LAN service to mesh peers. Aimed at operators bridging a LAN segment into the overlay from the edge router. For a non-OpenWrt host the same deployment is in ../how-to/deploy-gateway.md.
When to use the how-to guides instead
The tutorials here walk through one specific path each. The how-to guides under ../how-to/ are the operator recipes — alternative provisioning paths, less-common configurations, troubleshooting techniques. Once you have the shape of FIPS in your head from these tutorials, the how-tos are where you'll go to look up "how do I do X?" without being walked through the surrounding context.