fips/docs/tutorials/host-a-service.md

Host a Service of Your Own

In reach-mesh-services you used ordinary IPv6 tools to reach services on other mesh nodes. This tutorial flips the direction. You will bring up a small HTTP server on your machine, make a deliberate choice about which interface it binds to, and turn on the mesh firewall to keep the exposure to what you intended. By the end you will have hosted your first peer-reachable service and made an informed decision about who can reach it.

The whole exercise should take about twenty minutes. You should have already worked through persistent-identity so that the npub your service is reachable at does not change between restarts.

What you'll build

   ┌──────────────────────────────────────────┐
   │  your fips node                          │
   │                                          │
   │   python3 -m http.server                 │
   │      --bind <fips0-addr> 8080            │
   │                       │                  │
   │                       ▼                  │
   │   fips0  fd97:….:Y  ◀─── port 8080 open  │
   └────────────┬─────────────────────────────┘
                │
                │  reachable as
                │     http://<your-npub>.fips:8080/
                ▼
   any mesh peer that can route to <your-npub>.fips

You will have:

• A single-page HTTP server bound to fips0 only — not the public internet, not your LAN, just the mesh.
• The mesh firewall baseline active, default-deny on fips0 inbound, with one explicit drop-in that allows TCP/8080.
• A clear understanding of which interface choice corresponds to which audience.

Why bind interface matters

The single most important decision when hosting a service is which interface (and therefore which audience) the service is exposed to. This is true for every IPv6 service, not just FIPS — but FIPS makes it stark because your machine often has several interfaces with very different exposure profiles.

Bind interface = exposure surface. A typical FIPS host has at least two distinct audiences:

• fips0 (fd97:…, reachable as <your-npub>.fips) — reachable only from FIPS peers that have a working link to your node. Bound by Noise authentication and (optionally) the peer ACL.
• eth0 / wlan0 (your LAN address) — reachable from anyone on your local network segment, with no FIPS auth in the way.

When you run a server, the --bind argument decides which of these audiences sees the service. Binding to a specific address opts in to one audience. Binding to [::] or 0.0.0.0 opts in to all of them at once — including any you forgot you had.

Audit what's already listening. Bringing up fips0 adds a new audience to every service on this host that was already bound to 0.0.0.0 or [::]. SSH, your web server, a database — if any of them was listening on all interfaces before you joined the mesh, they are now reachable from mesh peers too. A quick ss -tulnp will show you everything currently listening and on which addresses. The mesh firewall (Step 5 below) is one way to bring those exposures back under explicit control; rebinding the affected services to a specific non-mesh address is another.

There is nothing FIPS-specific about this rule; it applies to SSH, web servers, databases, anything. FIPS just gives you the option of "mesh peers only" as a distinct audience, which most hosts otherwise don't have.

Step 1: Find your node's mesh address

You need the fd97:... address assigned to your fips0 adapter. Two equivalent ways to get it:

ip -6 addr show fips0

Look for the inet6 fd97:... line. The address up to the / is what you want.

Or via the daemon:

sudo fipsctl show status

The JSON has an ipv6_addr field — that is your address.

For the rest of this tutorial we will write the address as <your-fips0-addr>. Substitute the actual fd97:... value when you run the commands. Save it to a shell variable for convenience:

FIPS0_ADDR=$(ip -6 addr show fips0 | awk '/inet6 fd97:/ {print $2}' | cut -d/ -f1)
echo "$FIPS0_ADDR"

You should also know your npub from persistent-identity:

NPUB=$(sudo cat /etc/fips/fips.pub)
echo "$NPUB"

<your-npub>.fips and <your-fips0-addr> are two names for the same destination.

Step 2: Bring up an HTTP server bound to fips0

Make a small directory with one file in it so the server has something to serve:

mkdir -p /tmp/mesh-demo
echo '<h1>Hello from the mesh</h1>' > /tmp/mesh-demo/index.html
cd /tmp/mesh-demo

Start a Python HTTP server bound to your fips0 address:

python3 -m http.server --bind "$FIPS0_ADDR" 8080

Leave the server running. The terminal will show:

Serving HTTP on fd97:... port 8080 (http://[fd97:...]:8080/) ...

Two things to notice:

• The "Serving HTTP on …" line names your fd97:... address explicitly. Python is binding only to that one address.
• The default would have been 0.0.0.0 — which is not what you want here. Without --bind, the server would be reachable from your LAN and any public IP this host has, not just from the mesh.

Step 3: Verify the service locally

Open a second terminal. From the same host, fetch the page:

curl -6 "http://[$FIPS0_ADDR]:8080/"

Expect:

<h1>Hello from the mesh</h1>

Now fetch it by name. Both forms should work:

curl -6 "http://${NPUB}.fips:8080/"

The daemon's local DNS responder turned the npub-form name into the fd97:... address, and the request landed at your HTTP server.

What just happened. The kernel routed your local request via the loopback path because the destination address is assigned to one of your own interfaces. You exercised the client side (DNS, IPv6 socket open, HTTP request) and the server side (HTTP listener, response). What you have not yet verified is reachability from another mesh node. That is the next concern.

If you have fipstop available, open it now in another terminal and switch to the Node tab. The right-half of the Traffic block — the Listening on fips0 panel — should list a tcp row at port 8080 with a python(<pid>) Process column. The State column reads OPEN because the firewall has not been turned on yet; everything bound to fips0 is currently mesh-reachable. The yellow banner above the panel says "fips-firewall.service inactive — all listeners exposed". Both signals will flip in the next two steps.

Step 4: Reachability from a mesh node

Any mesh node — a direct peer, or a node several hops away — reaches your service the same way you reached test-us01 in reach-mesh-services: it looks up <your-npub>.fips, gets back your fd97:... address, opens a TCP connection to it, and the FIPS data plane carries the packets across the mesh to you. From the remote host the curl looks identical to yours:

curl -6 "http://${NPUB}.fips:8080/"

If you have a second machine on the mesh — or you can ask another operator to try it — this is the moment to confirm. A node that can already ping6 ${NPUB}.fips should also be able to fetch your page. If it can ping but the curl times out, jump to Troubleshooting — but most likely the firewall step in this tutorial has not happened yet, so a remote attempt right now will succeed straight through to your HTTP server.

That is the problem. With no firewall in place, any mesh node that can route to you — your direct peers, and every node beyond them in the mesh — can reach port 8080. You have not yet made a deliberate decision about whether you want that. The rest of this tutorial replaces the implicit "every port with a listener is reachable" with an explicit "only the ports I have opened are reachable, optionally only from specific mesh nodes." That is the firewall's job, and it is the only mechanism in play in the rest of this tutorial.

(There is a separate, unrelated control called the peer ACL that decides which npubs may establish a peer connection with your node at the transport layer. It is not part of the firewall and does not affect what is described below; Step 7 is a brief signpost to it.)

Step 5: Activate the mesh firewall baseline

FIPS ships a default-deny nftables baseline at /etc/fips/fips.nft that restricts inbound traffic on fips0 to ICMPv6 echo and conntrack replies. The baseline is not enabled by default — activation is an explicit step the operator has to take.

Activate it:

sudo systemctl enable --now fips-firewall.service

This loads the table immediately and arranges for it to load on every subsequent boot. Confirm:

sudo nft list table inet fips

You will see one chain named inbound hooked at input, roughly:

table inet fips {
    chain inbound {
        type filter hook input priority filter; policy accept;
        iifname != "fips0" return
        ct state established,related accept
        icmpv6 type echo-request accept
        counter packets 0 bytes 0 drop
    }
}

The chain admits ICMPv6 echo (so ping6 from any mesh node still works) and conntrack replies (so your outbound connections still get their replies back). Everything else inbound on fips0 hits the final counter ... drop.

What this changed. Your HTTP server is still running and still reachable from this same host (same-host traffic to fd97:... goes via the loopback path, which has iifname != "fips0" and short-circuits at the first rule). But any mesh node trying to reach fd97:...:8080 now has its TCP SYN dropped before it can reach your server. From the remote end the connection times out.

The fipstop panel reflects the change immediately: the yellow "firewall inactive" banner disappears, the panel title becomes a plain "Listening on fips0", and your tcp 8080 python(<pid>) row flips to DarkGray with filt in the State column. Every other row also goes DarkGray — none of them have an explicit accept rule yet, and the chain falls through to counter drop.

So the firewall is in the right shape but in the wrong state for our purpose: we want mesh nodes to reach port 8080. The next step opens that one port.

Step 6: Open port 8080 via a drop-in

Drop-ins live under /etc/fips/fips.d/ with the .nft suffix. Each file is included into the inbound chain at the marked point and may contain any nftables rule lines valid in that context.

Create one for your HTTP service:

sudo tee /etc/fips/fips.d/http-mesh-demo.nft >/dev/null <<'EOF'
tcp dport 8080 accept
EOF

Reload the firewall:

sudo systemctl reload-or-restart fips-firewall.service

Confirm the rule is live:

sudo nft list table inet fips

The inbound chain now contains your tcp dport 8080 accept rule between the conntrack rule and the final counter drop.

A curl from any mesh node will now reach the HTTP server. The path is: remote node's mesh data plane → forwarded across the mesh → your direct peer's link to you → fips0 ingress → inbound chain → matches tcp dport 8080 accept → delivered to the HTTP server.

In the fipstop panel, your tcp 8080 python(<pid>) row flips back to default White with OPEN in the State column on the next poll tick. No other row changes — they remain DarkGray filt because you have only opened this one port. The panel doubles as a security screen for the rest of the tutorial: any service whose row reads OPEN is mesh-reachable, anything DarkGray is filtered. If you later add a saddr-restricted drop-in (covered just below), the row will land at filt? rather than OPEN, signalling that the rule exists but is source-scoped — the panel deliberately does not classify restricted accepts as fully open.

If you only want to expose the service to a specific node or set of nodes, source-filter the rule. The address filter applies to the mesh-source address as it arrives on fips0, which is the originating node's address — not necessarily a direct peer. Replace the drop-in contents with something like:

ip6 saddr fd97:1234:5678:9abc:def0:1234:5678:9abc tcp dport 8080 accept

The source address is the node's mesh address, which it publishes in its fips.pub (and which you can resolve from its npub). For multiple nodes, use a set:

ip6 saddr {
    fd97:1111:2222:3333:4444:5555:6666:7777,
    fd97:8888:9999:aaaa:bbbb:cccc:dddd:eeee
} tcp dport 8080 accept

For the worked example, leave the drop-in unfiltered — any mesh node that can route to you can fetch your page.

Step 7: A note on the peer ACL

The firewall you just configured is the only control in scope for this tutorial. There is a separate, optional control called the peer ACL that you may run across in other docs; it is unrelated to the firewall and worth a sentence here only so you do not confuse the two.

The peer ACL decides which npubs may establish a peer connection with your node at the transport layer. It does not look at ports, drop-ins, or fips0 traffic. You do not need it for this tutorial.

For when you do:

• ../how-to/enable-nostr-discovery.md — operator recipe.
• ../reference/security.md § Peer ACL — file format, evaluation order, alias handling.

Step 8: Stop the server and tidy up

When you are done, stop the HTTP server in the first terminal with Ctrl-C. The drop-in stays in place; remove it if you do not want port 8080 reachable after the demo:

sudo rm /etc/fips/fips.d/http-mesh-demo.nft
sudo systemctl reload-or-restart fips-firewall.service

The fips-firewall.service itself can stay enabled — default-deny on fips0 is a sensible posture even with no extra services running. To turn it back off:

sudo systemctl disable --now fips-firewall.service

What you've learned

• Bind interface = audience. Binding to a specific address opts in to one audience; binding to wildcard (0.0.0.0 / [::]) opts in to all of them, including ones you forgot you had. For mesh-only exposure, bind to your fd97:... address. The fipstop Listening on fips0 panel marks wildcard binds with a trailing * after the process name as a reminder that the bind is not fips0-specific.
• Same-host loopback is misleading. A local curl to your own fd97:... address goes via the loopback path, not through fips0 ingress. To actually verify mesh-side reachability you need a second machine, or to read what the firewall is doing in nft list table inet fips.
• The mesh firewall is opt-in. fips-firewall.service is not enabled by default. Once it is enabled, fips0 is default-deny except for ICMPv6 echo and conntrack replies.
• Ports open via drop-ins. Each file under /etc/fips/fips.d/*.nft adds rules into the inbound chain. Source-filter with ip6 saddr to scope a port to specific mesh nodes.
• Two independent controls at two different layers. The firewall is a layer-3 filter on fips0: it controls which TCP/UDP ports are reachable and (optionally) which mesh source addresses may reach them. The peer ACL is a transport-layer admission filter on Noise handshakes: it controls which npubs may become direct peers of your node. They are unrelated — the ACL does not touch fips0 traffic, and the firewall does not look at npubs.

You now have the mental model for hosting any IPv6 service behind a deliberate exposure policy. The mechanics generalize: SSH on port 22, a database on port 5432, a custom protocol on its own port — same --bind rule, same drop-in shape.

Troubleshooting

• A remote mesh node cannot reach the service after the firewall reload. Check the drop-in syntax with sudo nft -c -f /etc/fips/fips.nft before reloading; a syntax error in any drop-in causes the whole table to fail to load and the previous rules persist. Then sudo nft list table inet fips to confirm your tcp dport 8080 accept rule is present in the inbound chain.
• Local curl works, remote curl times out. The packet is reaching fips0 ingress and being dropped by the baseline. Either your drop-in did not load (see above) or it has a source filter that excludes the remote node's address.
• Local curl fails after binding to fips0. Double-check that your FIPS0_ADDR matches the address shown in ip -6 addr show fips0. The Python server message also echoes the bound address — confirm it starts with fd97:, not 127.0.0.1 or ::.
• Address already in use from Python. Another process holds port 8080. Pick a different port (8081, 9000, …) for both the python3 -m http.server invocation and the drop-in.
• Watch the firewall counter to confirm drops. The counter ... drop line at the bottom of the chain increments on every dropped inbound packet. After a remote mesh node attempts to reach a port you have not opened, sudo nft list table inet fips will show the counter packet count rising.
• Use fipstop to spot-check listener and filter state. The Listening on fips0 panel on the Node tab shows every fips0-reachable listener and its current filter state. A row staying filt after you expected OPEN usually means the drop-in failed to load (a syntax error in any file under /etc/fips/fips.d/ aborts the whole reload, leaving the previous ruleset in place) or the drop-in carries a source filter and now reads filt? rather than OPEN.

What's next

• ground-up-mesh.md — Bring up two devices on a shared physical link — Ethernet, WiFi, or Bluetooth — with no pre-existing IP infrastructure between them. The second deployment mode of FIPS, where the mesh is the network rather than an overlay on top of one. Coexists with overlay peers; the same daemon carries both.

For more depth on the firewall and ACL surface:

• ../how-to/enable-mesh-firewall.md — operator recipes for the baseline, drop-in patterns, and how to fold the baseline into an existing nftables.conf.
• ../reference/security.md — consolidated security reference: nftables baseline rules, drop-in format, peer ACL semantics, default exposures by transport, threat-resistance matrix.
• ../design/fips-security.md — threat model, why the baseline is opt-in, the metadata- privacy posture.

If you want to host a service that is not on a FIPS node — say, an existing HTTP server on a regular LAN box — and expose it to mesh peers through a fips-gateway, that's the inbound port-forward mode: the gateway runs a mesh-side listener on fips0 and forwards to a LAN target. The operator recipe is at ../how-to/deploy-gateway.md#inbound-port-forwarding; a hand-held walk-through on an OpenWrt AP is at deploy-fips-gateway.md under "Advanced" in README.md.